Look at the problems related to PCB design

PCB design refers to the production of circuit boards at the lowest possible cost through the design of schematic drawings and circuit layout. In the past, this was usually done with expensive special tools, but now, with the free high performance

PCB design refers to the production of circuit boards at the lowest possible cost through the design of schematic drawings and circuit layout. In the past, this was usually done with expensive special tools, but now, with the growing popularity of free high-performance software tools such as DesignSpark PCB and design models, the design speed of circuit board designers has been greatly accelerated.

Although engineering designers know that a perfect design scheme is the best way to avoid problems, it is still a method that wastes both time and money, while addressing the symptoms rather than the root cause. For example, if problems are found in the electromagnetic compatibility (EMC) testing phase, it will cause a lot of cost investment, and even require adjustment and re production of the original design scheme, which will take several months.

Challenge

PCB layout is a problem that designers must face first. This problem depends on some contents in the drawing, and some devices need to be set together based on logical considerations. However, it should be noted that temperature sensitive elements, such as sensors, should be set separately from heat generating elements, including power converters. For designs with multiple power settings, 12V and 15V power converters can be set at different positions of the circuit board, because the heat and electronic noise generated by them will affect the reliability and performance of other components and circuit boards.

The above PCB components will also affect the electromagnetic performance of the circuit design, which is not only important for the performance and energy consumption of the circuit board, but also has a great impact on the economy of the circuit board. Therefore, all circuit board equipment sold in Europe must obtain the CE mark to prove that it will not interfere with other systems. However, this is usually only from the perspective of power supply. There are also many devices that emit noise, such as DC-DC converters and high-speed data converters. Due to the defects in the design of the circuit board, these noises can be captured by the channel and radiated as a small antenna, thus generating noise and abnormal frequency areas.

The problem of far field electromagnetic interference (EMI) can be solved by installing filters at noise points or using metal enclosures to shield signals. However, due attention should be paid to the equipment that can release electromagnetic interference (EMI) on the circuit board, which allows the circuit board to choose a cheaper shell, thus effectively reducing the cost of the entire system.

In the process of circuit board design, electromagnetic interference (EMI) is indeed a factor that must be paid attention to. Electromagnetic crosstalk can couple with the channel, which disrupts the signal into noise and affects the overall performance of the circuit board. If the coupling noise is too high, the signal may be completely covered. Therefore, more expensive signal amplifiers must be installed to restore normal. However, if the signal circuit layout can be fully considered at the beginning of the circuit board design, the above problems can be avoided. Because the design of the circuit board will be different according to different devices, different places of use, different heat dissipation requirements, and different electromagnetic interference (EMI) conditions, the design template will come into use.

Capacitance is also an important issue in circuit board design that cannot be ignored, because capacitance will affect the propagation speed of signals and increase the consumption of electricity. The channel will couple with the adjacent line or cross two circuit layers vertically, thus forming a capacitor unintentionally. The above problems can be solved relatively easily by reducing the length of parallel lines and installing kinks on one of the lines to cut off the coupling. However, it also requires engineering designers to fully consider the PCB production design principles, ensure that the design scheme is convenient for PCB manufacturing, and avoid any noise radiation caused by excessive line bending angle. The distance between lines may also be too close, which will create a short circuit between lines, especially at line bends. As time goes on, metal "whiskers" will appear. PCB design rule detection can usually mark areas where the loop risk is higher than normal.

This problem is particularly prominent in the design of the ground plane. A metal circuit layer may form coupling with all lines above and below it. Although the metal layer can effectively block noise, it will also generate associated capacitance, affect the running speed of the line, and increase power consumption.

As far as the design of multilayer PCB is concerned, the via design between different circuit board layers is probably the most controversial issue, because the via design will bring many problems to the production and manufacturing of circuit boards. The through-hole between the circuit board layers will affect the performance of the signal and reduce the reliability of the circuit board design, so it should be given full attention.